How do I configure my Cisco 112 Analogue Phone Adapter via VoIP Provider, Netphone Online App?
login to your router
go to http://192.168.1.109 (in the case of me but your internal, local IP address could be anything via DHCP. You can use a software program called Angry IP Scanner. Use this to find all your IP connected devices on your network in one quick micro-second. Well almost.
Anyway back to http://192.168.1.109 router cisco 112 analogue phone adapter setup and configuration. Simply follow a few easy steps and it’s installed and configured in less 3 minutes, sometimes less if you have all your username and passwords quickly accessible.
Visit your Cisco 112 analogue phone adapter routers administration default page.
(is the default login but do change the default admin password).
Once you have completed the above for line 1 settings for your cisco 112 analogue phone adapter then click the submit button and your cisco 112 analogue phone adapter device will reboot and save your settings.
Click on “Voice” and your page like the above should display similar, your registration status may say it’s not connected or registered but that’s OK, we’ll fix this up now.
Cisco 112 analogue phone adapter line 1 details.
Line 1 Status
Hook State: On Registration State: Registered
Last Registration At: 3/8/2018 01:18:25 Next Registration In: 120 s
Line Enable: YES
Streaming Audio Server (SAS)
SAS Enable: SAS DLG Refresh Intvl:
SAS Inbound RTP Sink:
NAT Mapping Enable: NAT Keep Alive Enable:
NAT Keep Alive Msg:
NAT Keep Alive Dest:
SIP ToS/DiffServ Value:
SIP CoS Value:
RTP ToS/DiffServ Value:
RTP CoS Value:
Network Jitter Level: Jitter Buffer Adjustment:
SIP Transport: SIP Port:
SIP 100REL Enable: EXT SIP Port:
Auth Resync-Reboot: SIP Proxy-Require:
SIP Remote-Party-ID: SIP GUID:
SIP Debug Option: RTP Log Intvl:
Restrict Source IP: Referor Bye Delay:
Refer Target Bye Delay:
Referee Bye Delay:
Refer-To Target Contact: Sticky 183:
Auth INVITE: Reply 182 On Call Waiting:
Use Anonymous With RPID: Use Local Addr In FROM:
Call Feature Settings
Blind Attn-Xfer Enable: MOH Server:
Xfer When Hangup Conf: Conference Bridge URL:
Conference Bridge Ports: Enable IP Dialing:
Feature Key Sync:
Proxy and Registration
Use Outbound Proxy: Use OB Proxy In Dialog:
Register: Make Call Without Reg:
Ans Call Without Reg:
Use DNS SRV: DNS SRV Auto Prefix:
Proxy Fallback Intvl:
Proxy Redundancy Method:
Mailbox Subscribe URL:
Mailbox Subscribe Expires:
Auto Register When Failover:
Use Auth ID:
Resident Online Number:
Supplementary Service Subscription
Call Waiting Serv: Block CID Serv:
Block ANC Serv: Dist Ring Serv:
Cfwd All Serv: Cfwd Busy Serv:
Cfwd No Ans Serv: Cfwd Sel Serv:
Cfwd Last Serv: Block Last Serv:
Accept Last Serv: DND Serv:
CID Serv: CWCID Serv:
Call Return Serv: Call Redial Serv:
Call Back Serv: Three Way Call Serv:
Three Way Conf Serv: Attn Transfer Serv:
Unattn Transfer Serv: MWI Serv:
VMWI Serv: Speed Dial Serv:
Secure Call Serv: Referral Serv:
Feature Dial Serv: Service Announcement Serv:
Reuse CID Number As Name: CONFCID Serv:
Preferred Codec: Second Preferred Codec:
Third Preferred Codec: Use Pref Codec Only:
Use Remote Pref Codec: Codec Negotiation:
G729a Enable: Silence Supp Enable:
G726-32 Enable: Silence Threshold:
FAX V21 Detect Enable: Echo Canc Enable:
FAX CNG Detect Enable: FAX Passthru Codec:
FAX Codec Symmetric: DTMF Process INFO:
FAX Passthru Method: DTMF Process AVT:
FAX Process NSE: DTMF Tx Method:
FAX Disable ECAN: DTMF Tx Mode:
DTMF Tx Strict Hold Off Time:
FAX Enable T38:
Hook Flash Tx Method: FAX T38 Redundancy:
FAX T38 ECM Enable: FAX Tone Detect Mode:
Symmetric RTP: FAX T38 Return to Voice:
Modem Line: RTP to Proxy in Remote Hold:
FXS Port Polarity Configuration
Idle Polarity: Caller Conn Polarity:
Callee Conn Polarity:
Netphone Online App works perfectly with your cisco 112 analogue phone adapter.
Netphone Online App – Cisco 112 Analogue Phone adapter settings should be exactly as shown, if you do not know the settings or need them configured for you, remotely, please email firstname.lastname@example.org or contact us on Skype ID on email@example.com.
Once you are absolutely sure of the exact same settings for your Cisco 112 analogue phone adapter above then all will work.
Click on the submit button and your cisco 112 analogue phone adapter will reboot and save your settings.
Cisco 112 analogue phone adapter goes for online retail price of $140 including FREE delivery Australia-wide and pre-configured options is available 24×7, remotely via Teamviewer or Remote Desktop.
Once your router is rebooted and you get line status is registered then you should be able to make a phone call and also receive a phone call.
Your phone number and all the details for your Cisco 112 analogue phone adapter is setup for you and all details, including your phone number is assigned to your username when you sign up to the Netphone Online App. Bring it on.
Any troubles? Cisco 112 Analogue phone adapters, direct support is available as follows, online.
Skype ID: firstname.lastname@example.org